Our Team


Comments

  1. Master PipeOctober 4, 2021 at 5:16 AM

    I think this post is excellent and so informative, thank you for taking the time to write it!

    ReplyDelete
  2. korusNovember 3, 2021 at 5:07 AM

    It's a really informative post, Also visit Stainless Steel 310/310s Seamless Pipes Manufacturers

    ReplyDelete
  3. Girish Metal IndiaNovember 5, 2021 at 5:20 AM

    Great blog! Please visit Stainless Steel round bar manufacturer.

    ReplyDelete
  4. Manibhadra FittingsNovember 8, 2021 at 2:17 AM

    It's Great...! Also Read Conex Valve Supplier in India

    ReplyDelete
  5. Sanjay Metal IndiaNovember 8, 2021 at 3:24 AM

    Great Article! Also know about Stainless Steel Flanges

    ReplyDelete
  6. Manan Steels and MetalsMarch 16, 2022 at 11:17 PM


    Your blog is amazing, i really appreciate your work
    Visit: Round Bar Manufacturer
    Website:Manan Steel

    ReplyDelete
  7. MaxgrowMarch 31, 2022 at 12:10 AM

    This comment has been removed by the author.

    ReplyDelete
  8. Nippon Alloys IncApril 7, 2022 at 10:01 PM

    Nice info also check out Alloy 20 Round Bar Manufacturer or Alloy 20 Round Bar Manufacturers at Nippon Alloys Inc. We also manufacture products like Fillers Wire and Forged Circle and Rings.

    ReplyDelete
  9. AnonymousApril 9, 2022 at 6:14 PM

    The King Casino Archives - Hertzaman
    The King Casino Archives, including news, articles, videos, address, gaming info, 메이피로출장마사지 The King Casino & Hotel in Henderson, NV is septcasino.com one herzamanindir.com/ of the febcasino newest hotels and งานออนไลน์ motels on

    ReplyDelete
  10. BHANSALI STEELMay 6, 2022 at 2:27 AM

    Nice Info, also check wire mesh manufacturer in India and visit our website at Bhansali Steel.We Manufacture various types of steel products like Perforated Sheet and Welded Wire Mesh.

    ReplyDelete

Post a Comment

Popular posts from this blog

NFPA 13 PRESSURE TEST PROCEDURES

NFPA 13 PRESSURE TEST PROCEDURES  (Aboveground Fire Systems): A hydrostatic test is a pressure test to reveal the presence of leaks in the piping system. For fire protection systems, the piping is pressurized to 200 psi (13.8 bar) for a period of 2 hours.  During this time period, the system piping is inspected for leaks.  Leaks in the piping system are revealed either by observation of water droplets or by a reduction in test pressure. Any leaks or reduction in test pressure necessitates a repair of the pipe joint involved and a retest to verify that the leak has been repaired. In cases where high pressure exists, the standard requires that the test pressure be 50 psi (3.5 bar) in excess of the normal system pressure if the resultant test pressure will be greater than 200 psi (13.8 bar).. By NFPA: Unless permitted by 24.2.1.2 through 24.2.1.8, all piping and attached appurtenances subjected to system working pressure shall be hydrostatically tested ...
Read more

Wet Pipe Fire Sprinkler System

Image
Wet Pipe Fire Sprinkler System Wet pipe sprinkler systems are the simplest and most common fire suppression method on the market today. This fire sprinkler system is cost efficient and low maintenance. They are comprised of pipes that constantly contain pressurized water. When a sprinkler activates this water is immediately discharged onto the fire.  The first automatic, closed-type sprinkler head immediately discharges water, as more individual sprinkler heads are subsequently activated by heat, they too will discharge water onto the fire until it is controlled or extinguished. Wet pipe fire sprinkler systems can be installed in buildings not susceptible to freezing (i.e., where temperatures are above 40 degrees Fahrenheit).   Typically, a Fire Sprinkler Systems are made up from a series of components including; Stop Valve, Alarm Valve, Fire Sprinkler (head), Alarm Test Valve and Motorized Alarm Bell (Gong). In addition to this there are additional components ...
Read more

Fire Pump Foundation

Fire Pumps Foundations NFPA 20 (2013 edition) Section 6.4.3 states that centrifugal pumps shall be securely attached to a solid foundation in such a way that proper pump shaft and driver shaft alignment is ensured. Foundation shall be sufficiently substantial to form a permanent and rigid support for the base plate (6.4.4). A substantial foundation is important to form a permanent and rigid support for the base plate. The foundation, preferably made of reinforced concrete, needs to be designed to adequately carry the loading of the pump, driver, and other equipment (A.6.4.4) The pump need to be anchored to the foundation with foundation bolts to form a single structural unit. After the pump has been properly secured to the foundation and proper alignment has been verified, the pump may then be grouted to the foundation. The base plate should be completely filled with grout, and it is desirable to grout the leveling pieces, shims, or wedges in place. Foundation bolt...
Read more